Showing posts with label Amplifier Schematic. Show all posts
Showing posts with label Amplifier Schematic. Show all posts
Monday, August 15, 2011
Class B audio amplifier based on TDA1553
Here is the circuit of a Class B audio amplifier based on TDA1553. TDA1553 is a monolithic audio amplifier class B, containing 2 x 22 watt amplifier in bridge configuration load attached. The amplifier operates from 12V DC and develops intentionaly for car audio applications. The IC also has a lot of good features such as short circuit protection, protection of the load dump, reverse polarity protection, speaker protection, etc.
In the circuit, C5 and C4 are decoupling capacitors C3 input, while setting the delay for speaker protection. C1 and C2 are filter capacitors of the offer.
Notes :
- Assemble the circuit on a good quality PCB.
- Use 12V DC for powering the circuit.
- The circuit can deliver 22W per channel into 4 ohm speakers.
- Fit the IC with a proper heat sink.
Sunday, June 19, 2011
16W Bridge Amplifier using LM383
The afterward diagram is 16W Bridge audio amplifier circuit. The ambit congenital based 2 pieces of ability IC LM383 in arch connection, so this amplifier is an arch amplifier.
This is an old amplifier, LM383 is discontinued, so this LM383 ability be difficult to find. You can use ECG1232, TDA2002 or TDA2003 as the alter for LM383. Take a agenda that a heatsink bowl is appropriate to abstain overheating on the ICs.
Sunday, May 22, 2011
18W Amplifier Schematic Circuit
18W Amplifier Schematic Circuit Part List
P1_____________22K Log. Potentiometer (Dual-gang for stereo)
R1______________1K 1/4W Resistor
R2______________4K7 1/4W Resistor
R3____________100R 1/4W Resistor
R4______________4K7 1/4W Resistor
R5_____________82K 1/4W Resistor
R6_____________10R 1/2W Resistor
R7_______________R22 4W Resistor (wirewound)
R8______________1K 1/2W Trimmer Cermet (optional)
C1____________470nF 63V Polyester Capacitor
C2,C5_________100µF 3V Tantalum bead Capacitors
C3,C4_________470µF 25V Electrolytic Capacitors
C6____________100nF 63V Polyester Capacitor
D1___________1N4148 75V 150mA Diode
IC1________TLE2141C Low noise, high voltage, high slew-rate Op-amp
Q1____________BC182 50V 100mA NPN Transistor
Q2____________BC212 50V 100mA PNP Transistor
Q3___________TIP42A 60V 6A PNP Transistor
Q4___________TIP41A 60V 6A NPN Transistor
J1______________RCA audio input socket
Power supply parts:
R9______________2K2 1/4W Resistor
C7,C8________4700µF 25V Electrolytic Capacitors
D2_____________100V 4A Diode bridge
D3_____________5mm. Red LED
T1_____________220V Primary, 15 + 15V Secondary, 50VA Mains transformer
PL1____________Male Mains plug
SW1____________SPST Mains switchThursday, May 13, 2010
1.5V Amplified Ear Circuit Diagram
Device purpose:
This circuit, affiliated to 32 Ohm impedance mini-earphones, can ascertain actual alien sounds. Useful for theatre, cinema and address goers: every chat will be acutely heard. You can additionally accept to your television set at a actual low volume, alienated to bother ancestors and neighbors. Even if you accept a faultless hearing, you may ascertain abrupt sounds application this device: a alien bird twittering will assume actual abutting to you.
Circuit operation:
The affection of the ambit is a constant-volume ascendancy amplifier. All the signals picked-up by the microphone are amplified at a connected akin of about 1 Volt aiguille to peak. In this address actual low amplitude audio signals are awful amplified and aerial amplitude ones are limited. This operation is able by Q3, modifying the bent of Q1 (hence its AC gain) by agency of R2. A noteworthy affection of this ambit is 1.5V array operation. Typical accepted drawing: 7.5mA.
Notes:
- Due to the constant-volume control, some users may consider P1 volume control unnecessary. In most cases it can be omitted, connecting C6 to C3. In this case use a SPST slider or toggle switch as SW1.
- Please note the stereo output Jack socket (J1) connections: only the two inner connections are used, leaving open the external one. In this way the two earpieces are wired in series, allowing mono operation and optimum load impedance to Q4 (64 Ohm).
- Using suitable miniature components, this circuit can be enclosed in a very small box, provided by a clip and hanged on one's clothes or slipped into a pocket.
- Gary Pechon from Canada reported that the Amplified Ear is so sensitive that he can hear a whisper 7 meters across the room.
He hooked a small relay coil to the input and was able to locate power lines in his wall. He was also able to hear the neighbor's stereo perfectly: he could pick up the signals sent to the speaker voice coil through a plaster wall.
Gary suggests that this circuit could make also a good electronic stethoscope.
Sunday, April 18, 2010
Schematic Audio Amplifier Circuit 200W
Load Resistance : 8ohms
Input impedance : 55K
Maximum supply voltage : (+95v)-0-(-95v)
Recommended supply voltage : (+66v)-0-(-66v)
This complete aerial quality, low babble address audio ability amplifier is based about the Hybrid Integrated Ambit STK4050 bogus by Sanyo. The ambit incorporates aggregate and has a best music achievement ability of 200W.The ambit incorporates an on lath ability supply; therefore, alone centre broke agent is appropriate to ability the circuit. I t has actual acceptable affection sound. U can use it with your Home Theatre your PC & etc... You can additionally use it as Subwoofer Amplifier.
It is a bunched amalgamation for THIN-TYPE Audio sets. Easy Heatsink architecture to banish calefaction generated in THIN-TYPE audio sets. Constant-Current ambit to Reduce accumulation switch-ON and switch-OFF shock noise. External accumulation switch-On and switch-OFF shock babble muting, Load circumlocute protection, thermal abeyance and added circuits can be tailored-designed.
50Watt Audio Power Amplifier Circuit with LM3876
My account of architecture of this activity was to advance a bunched architecture for a stereo amplifier can be chip by a amiss (but the complete affection conscious!) Living apprentice at a university or a academy dormitory.
The amplifier feeds a brace of speakers with two LM3876 amplifier chip circuits (50 watts per channel), or a brace of headphones Meier Crossfeed through a clarify and a bifold OPA2134 Opamp. There are four selectable band inputs, and achievement buffers with band akin for the registry. The architecture with readily attainable apparatus of acceptable quality, and is disconnected into four BPC, a ability amplifier for anniversary channel, for the diet board, and for the pre-amp / headphone driver.
The achievement selector is beatific to pins J1 and J3. Looking at the larboard channel, C1 and R2 anatomy a low canyon clarify with a-3dB point of 40 kHz, which rejects any RF arrest best up on the interconnections. R2 additionally includes the impedance of the device, in this case, 47k ohms. R1 ensures Opamp U1 is presented with an impedance according to its two inputs, accord to convalescent the achievement of the distortions declared in the datasheet OPA2134.
The amount of R1 (9K1) is universally accessible, abutting to the amount of the alongside aggregate of R3 and R4 (22k and 15k, respectively). R3 and R4 set the accretion at that time, aloof beneath 2.5 in this case. This gives abounding amplitude for a advanced ambit of arresting sources, which could be as abundant as 3VRMS. In this case, the aiguille achievement voltage of 10.6V would be accomplished with the activity to accumulation ± 15V.
This antecedent accretion brings the arresting to a akin that the achievement of the aggregate can advance the ability amp circuits anon after any added benefit, and allows the helmet of the disciplinarian ambit to accomplish with a low gain, gives lower babble level. C7 forms 100kHz a lowpass clarify with R3, to abatement on the accretion of accord at actual aerial frequency, and to advice advance adherence in the Opamp. It is not carefully all-important for the proposed OPA2134 allows the unit, but bottomward acting cheaper but added acceptable cadence device, such as the NE5532, if budgets are tight. C19 brace the AC achievement of this appearance for aggregate control, and with a 50k potentiometer, the-3dB point of the acknowledgment of the headphone amps at 1.4Hz (power amp has added HIGH PASS FILTER). The capacitor is actual important because all the added stages are DC accompanying and DC C19 prevents any of the antecedent components, addition and presentation of headphones or speakers.
Resistance R9 binds the assembly of inputs to a recording accessory like a VCR or mini-disc. This helps to anticipate the antecedent actuality loaded in the diet of both the accretion date ascribe and the recording accessory and protects the source, the achievement should be shorted to apple for a acumen whatsoever. The achievement from J5 and J6 are alien into the aggregate ascendancy pot, which should be acceptable quality. Finally, C3 to C6 and accommodate decoupling of the ability accumulation rails, C5 and C6 aerial abundance decoupling, C3 and C4 lower decoupling.
Audio Amplifier Circuits 10W with Bass-boost
Parts:P1 22K Log.Potentiometer (Dual-gang for stereo)
P2 100K Log.Potentiometer (Dual-gang for stereo)
R1 820R 1/4W Resistor
R2,R4,R8 4K7 1/4W Resistors
R3 500R 1/2W Trimmer Cermet
R5 82K 1/4W Resistor
R6,R7 47K 1/4W Resistors
R9 10R 1/2W Resistor
R10 R22 4W Resistor (wirewound)
C1,C8 470nF 63V Polyester Capacitor
C2,C5 100uF 25V Electrolytic Capacitors
C3,C4 470uF 25V Electrolytic Capacitors
C6 47pF 63V Ceramic or Polystyrene Capacitor
C7 10nF 63V Polyester Capacitor
C9 100nF 63V Polyester Capacitor
D1 1N4148 75V 150mA Diode
IC1 NE5532 Low noise Dual Op-amp
Q1 BC547B 45V 100mA NPN Transistor
Q2 BC557B 45V 100mA PNP Transistor
Q3 TIP42A 60V 6A PNP Transistor
Q4 TIP41A 60V 6A NPN Transistor
J1 RCA audio input socket
Power supply parts:
R11 1K5 1/4W Resistor
C10,C11 4700uF 25V Electrolytic Capacitors
D2 100V 4A Diode bridge
D3 5mm. Red LED
T1 220V Primary, 12 + 12V Secondary 24-30VA Mains transformer
PL1 Male Mains plug
SW1 SPST Mains switch
Comments:
This design is based on the 18 Watt Audio Amplifier, and was developed mainly to satisfy the requests of correspondents unable to locate the TLE2141C chip. It uses the widespread NE5532 Dual IC but, obviously, its power output will be comprised in the 9.5 - 11.5W range, as the supply rails cannot exceed ±18V.
As amplifiers of this kind are frequently used to drive small loudspeaker cabinets, the bass frequency range is rather sacrificed. Therefore a bass-boost control was inserted in the feedback loop of the amplifier, in order to overcome this problem without quality losses. The bass lift curve can reach a maximum of +16.4dB @ 50Hz. In any case, even when the bass control is rotated fully counterclockwise, the amplifier frequency response shows a gentle raising curve: +0.8dB @ 400Hz, +4.7dB @ 100Hz and +6dB @ 50Hz (referred to 1KHz).
Notes:Can be directly connected to CD players, tuners and tape recorders.
Schematic shows left channel only, but C3, C4, IC1 and the power supply are common to both channels.
Numbers in parentheses show IC1 right channel pin connections.
A log type for P2 ensures a more linear regulation of bass-boost.Don't exceed 18 + 18V supply.
Q3 and Q4 must be mounted on heatsink.
D1 must be in thermal contact with Q1.
Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not critical.
Set the volume control to the minimum and R3 to its minimum resistance.
Power-on the circuit and adjust R3 to read a current drawing of about 20 to 25mA.Wait about 15 minutes, watch if the current is varying and readjust if necessary.
A correct grounding is very important to eliminate hum and ground loops. Connect in the same point the ground sides of J1, P1, C2, C3 &C4. Connect C9 at the output ground.
Then connect separately the input and output grounds at the power supply ground.
Technical data:
Output power: 10 Watt RMS @ 8 Ohm (1KHz sinewave)
Sensitivity: 115 to 180mV input for 10W output (depending on P2 control position)
Frequency response: See Comments above
Total harmonic distortion @ 1KHz: 0.1W 0.009% 1W 0.004% 10W 0.005%
Total harmonic distortion @ 100Hz: 0.1W 0.009% 1W 0.007% 10W 0.012%
Total harmonic distortion @10KHz: 0.1W 0.056% 1W 0.01% 10W 0.018%
Total harmonic distortion @ 100Hz and full boost: 1W 0.015% 10W 0.03%
Max. bass-boost referred to 1KHz: 400Hz = +5dB; 200Hz = +7.3dB; 100Hz = +12dB; 50Hz = +16.4dB; 30Hz = +13.3dB
Subscribe to:
Posts (Atom)